If they are dead flat then bingo - nailed it - however if the laser wobbles or appears to want to creep away from anything other than a perfectly flat line of oscillation (Flo), we'll rotate the shaft a degree or two one way or the other until I get that flat line. Then we'll clamp the butt of the shaft and mount a laser to the tip and twang it along the intended target line and observe the oscillations of the laser against a near by wall. Once we find N1, we'll mark a line over some painters tape and this is the spot that should be aligned at the target. EQ1-NX fairway woods are capable of being bent up to 2° to allow proper lie fitting when assembled to conventional fairway wood lengths.We put the shaft in a Neufinder and find the softest axis of the shaft, this is called N1 which refers to the natural bend plane of the shaft which is the spot the shaft wants to snap to when it's placed under load. The spec lie angle of 60* for each EQ1-NX fairway wood is created for assembly to the single length option between 40” and 41”.
SPINE ALIGN GOLF CLUBS DRIVER
For single length use we recommend a set makeup of #3/#5 for better ball strikers or players with a driver clubhead speed over 95mph and a set makeup of #4/#7 for average players or any golfers with a driver clubhead speed under 95mph. Any length in between 40” and conventional fairway wood lengths is also capable for an even wider range of fitting options. EQ1-NX Hybrids are capable of being bent up to 3° to allow proper lie fitting when assembled to conventional hybrid lengths.Įach EQ-1-NX fairway wood head is produced with the ability to add up to a maximum of 30g to achieve normal swingweights at a 40” to 41”single length to complement the EQ1-NX single length irons and hybrids. The spec lie angle for each EQ1-NX hybrid is 63° to match the EQ1-NX single length irons. The four different weight bores allow for maintaining the best CG position low and center located, as well as to be able to increase the trajectory with the new twin rear sole weight bores.
SPINE ALIGN GOLF CLUBS FULL
0.335” bore to accept any S2S Hybrid shaft. Though the EQ1-NX hybrid heads can be reamed to accept any 0.370” iron shaft, we recommend using an appropriate S2S 0.335” graphite hybrid shaft when matching the EQ1-NX hybrids to the EQ1-NX irons in a full single length set makeup.Īvailable in #4(20*), #5(24*), #6(28*) in RH to match the lofts and loft gaps of the EQ1-NX irons. High strength steel, thin variable thickness face, high COR design. Any length in between 8-iron and conventional hybrid lengths is also capable for an even wider range of fitting options.
Natural head weight specification of each EQ1-NX hybrid head also allows assembly to conventional hybrid lengths of #4(38”-39”), #5(37.5”-38.5”), #6(37”-38”). Traditional GW and SW profile shapes are combined with milled faces and a custom sole grind make the wedges a great choice even if they were standalone wedges and not part of the single length design.Ģ75g head weight with hosel weight bore allows assembly to any single length between 35.5” and 37.5” while still being able to achieve a reasonable range of swingweight/MOI (depending on shaft weight and grip weight).Įach EQ-1-NX hybrid head is produced with the ability to add up to a maximum of 30g to achieve normal swingweights at 8-iron single length to match the EQ1-NX single length irons. Low number irons are better matched with their loft to CG position to achieve preferred shot shape/height and allow a wider range of players to be able to effectively hit the #5 and 6 irons to fly and carry with proper distance gaps. The hollow body construction also enables the CG progression and uniform impact sound between the high COR and conventional COR heads in the set. The hollow body design throughout the set increases the MOI of each head by removing all mass from the inside of the head to be distributed all around the CG.
Enabled by the new 2-piece hollow body design, the Center of Gravity moves progressively through the set from lowest and most rear located on the #5 iron to highest and most forward located on the GW and SW to achieve more consistent shot shape and shot height for each iron in the set.
0 kommentar(er)
